Item no.: 1016331
GTIN/EAN: 4250234563314
€200.57 -5%
previously €210.86 Immediately available, 2 - 3 days delivery time within Germany.
Delivery times for other countries see here.
• Light stand for indoor and outdoor use
• Flexible working height from 162 - 730 cm
• Maximum load capacity 22.5 kg
• Air cushioned light stand
• 5/8” spigot with a 1/4” thread
Product information "Walimex pro AIR Jumbo 730 Light Stand Max height 730 cm, Load Capacity 22.5 kg, Light Stand with Air Cushioning, Lightweight Aluminium Design, Tripod for Photo Studios, Film Sets and Outdoor Use"
Robust Light Stand for Professional Photo Studios
The Walimex pro Jumbo AIR 730 cm Light Stand has a maximum height of 7.3 m, and it is perfect for studio lighting. You can adjust the height of the light stand from 162 - 730 cm. It can support flash heads, reflectors and other pieces of photography equipment weighing up to 22.5 kg. The legs on the stand can be adjusted and they have diameters of 45, 40, 36, 32, 28 and 25 mm. The diameter of the light stand is 158 cm.
Air Cushioned Light Stand
The air cushioning feature will stop your light stand from suddenly slipping or moving down and this will also protect your photography equipment from getting damaged. This design enables you to slowly and carefully lower the light stand.
Compatible with a Wide Range of Photography Accessories
The tripod is equipped with a removable 5/8” spigot adapter and a 1/4” thread. It is compatible with lots of different studio lighting, flash heads and other photography and videography accessories. It also comes with a light stand bag, which makes it easy to carry and store when it’s not in use.
Securing Your Light Stand
If your light stand is over 3 metres, we recommend securing it with tripod weights or sandbags. This minimises the risk of it tipping over and getting damaged. However, the maximum load capacity of 22.5 kg does not apply when the light stand has been fully extended.
What’s Included:
- x1 Walimex pro Light Stand Jumbo AIR 730 cm
- x1 light stand bag
- x2 spigot adapter with a 1/4” thread
The Walimex pro Jumbo AIR 730 cm Light Stand has a maximum height of 7.3 m, and it is perfect for studio lighting. You can adjust the height of the light stand from 162 - 730 cm. It can support flash heads, reflectors and other pieces of photography equipment weighing up to 22.5 kg. The legs on the stand can be adjusted and they have diameters of 45, 40, 36, 32, 28 and 25 mm. The diameter of the light stand is 158 cm.
Air Cushioned Light Stand
The air cushioning feature will stop your light stand from suddenly slipping or moving down and this will also protect your photography equipment from getting damaged. This design enables you to slowly and carefully lower the light stand.
Compatible with a Wide Range of Photography Accessories
The tripod is equipped with a removable 5/8” spigot adapter and a 1/4” thread. It is compatible with lots of different studio lighting, flash heads and other photography and videography accessories. It also comes with a light stand bag, which makes it easy to carry and store when it’s not in use.
Securing Your Light Stand
If your light stand is over 3 metres, we recommend securing it with tripod weights or sandbags. This minimises the risk of it tipping over and getting damaged. However, the maximum load capacity of 22.5 kg does not apply when the light stand has been fully extended.
What’s Included:
- x1 Walimex pro Light Stand Jumbo AIR 730 cm
- x1 light stand bag
- x2 spigot adapter with a 1/4” thread
Safety Instructions
Download the full set of the instructions before setting up and using your device.
Carefully read through the full set of instructions before using your product for the first time. The instructions include all the important information that you will need to know about the product in order to avoid injuries and damage to your possessions.
Risk of Injury Due to Improper Use
Be careful not to trap your fingers in the struts on the tripod legs when folding your tripod.
Please note that lamp tripods must be set up on a sufficiently strong, level surface to ensure maximum stability and load-bearing capacity.
Please follow the safety information in the manual regarding the maximum load capacity for your tripod.
Please note that the specified load capacity applies to any equipment that is placed in the middle of the tripod. Depending on the equipment used, the maximum load capacity may differ from the specified maximum load. When using a boom, it is recommended to use suitable counterweights.
Please note that moisture can damage the parts on the middle column, and this may reduce the holding force and the parts on the centre column can start to slope downwards under heavy loads. Therefore, if necessary, dry the parts on the centre column with a soft, absorbent cloth (e.g. made of cotton).
After using your tripod for a long period of time, you may have to tighten the screws on the tripod clamps. Not enough tension reduces the maximum holding force of the tripod. Make sure that the clamps are tight, but do not tighten them too much. If the torque is too tight, the parts on the centre column may no longer be able to be extended properly.
When adjusting the centre column with mounted equipment, for your own safety and to protect the installed equipment, make sure that you hold the centre column with one hand while loosening the locks before loosening the tripod locks.
Do not move a loaded tripod with an extended centre column. You should only move it very carefully by holding it and gently pushing it. When heavy camera equipment is fitted onto a tripod and the large centre column has been extended, this can quite often cause a very sudden leverage effect. The lamp tripod has a top-heavy design when camera equipment has been fitted onto the top, therefore, be careful that it does not tip over and damage any camera equipment or cause any injuries.
When using heavy equipment, especially when the tripod has been fully extended, you may have to stabilise your tripod by adding weight to the legs. For this, we would recommend using special sandbags or tripod weights. These will ensure that your tripod is stable. You can also use safety ropes when using a tripod at different heights. They offer added stability for your tripod.
Using tripod castors:
Always lock the castors into place when you are not moving your tripod.
Manufacturer
Walser GmbH
- Wilhelm-Lexis-Str. 8
- 52249 Eschweiler
- DE
service@fotowalser.com
Properties "Walimex pro AIR Jumbo 730 Light Stand Max height 730 cm, Load Capacity 22.5 kg, Light Stand with Air Cushioning, Lightweight Aluminium Design, Tripod for Photo Studios, Film Sets and Outdoor Use"
Anzahl Stativsegmente: | 6 |
---|---|
Ausziehbar: | Yes |
Battery included: | No |
Battery required: | No |
Colour: | black |
Dimensions: | 1510 x 100 x 100 mm |
Durchmesser 1. Stativsegment (v.u.): | 45 Millimeter |
Durchmesser 2. Stativsegment (v.u.): | 40 Millimeter |
Durchmesser Standfläche max.: | 158 Zentimeter |
Dämpfung verbaut: | Yes |
Gewicht Stativ: | 5500 Gramm |
Main material: | aluminium, plastic |
Material Stativbeine: | Aluminium |
Material Verschlussklemmen: | Aluminium |
Max. Traglast Stativ: | 22.5 Kilogramm |
Max. working height: | 730 Zentimeter |
Min. working height: | 162 Zentimeter |
Minimales Packmaß: | 151 Zentimeter |
Mögliche Anschlüsse: | 1/4-Zoll-Gewindeanschluss, 5/8-Spigot (16-mm-Zapfen) |
Product type: | Studiostativ |
Transporttasche Stativ enthalten: | Yes |
Data according to manufacturer. Subject to alterations. Errors expected.